Hi-lux sight on a Model 94
Hi I have a Winchester Model 94, 30-30 and I’m trying to “install” it a Hi-Lux Vintage sight. I have the kit that came specifically for the Model 94, but I’m having problems with the screws that should...
View ArticleShotgun Stocks
Anybody know anyone in the North Georgia area who cuts adjustable combs in shotgun stocks?
View ArticleRace gun (Revolver)
Anybody got any experience modifying a single action revolver to a race gun. Milling the bolt and cylinder, putting a stop block, lighter springs, and a fanning hammer? I'm kinda of interested in...
View ArticleOpening up choke tubes
Hey Y'all does one know or recommend a place in Nort Ga that opens up choke tubes. I have a old 16 gauge SxS I would like to get looked at. Thanks
View ArticleGunsmith for Winchester 101
I am looking for a quality gunsmith to rebuild a Winchester 101. I'm thinking I need new springs, etc. I am in the Athens/monroe area Call. Anybody close by that you could highly recommend?
View ArticleBeretta A400 trigger
Just purchased an A400 Xplor, the trigger pull is right at six# before it breaks. That’s a little heavy, my Beretta O/U breaks at about three #. Any way to improve it? Thanks.
View ArticleStar BM slide locking
I suggested my friend buy a Star BM as his first and only defensive handgun. He wasn't willing to spend much money, and this one seems like a bargain to $200. And he was only interested in older...
View ArticleGun Restoration
I have 2 of my grandfather's guns that I am thinking about getting restored. One is a single shot 20 GA that has a cracked butt. The other is a single shot 22 that is held together with electrical...
View ArticleSCOPING DADDY'S "DEER RIFLE" !!
Daddy had this Mosin Nagant before I was born. The first person to sporterize it did an excellent job and even made a good looking, permanently attached front sight and made it the correct height. It...
View ArticleChristensen 7mm-08 Bolt Issue
I took my new Christensen Mesa 7mm-08 REM to the range today to start the barrel break-in. I got everything set up and put two shells in the rifle, started closing the bolt, and for some reason the...
View ArticleRebarrel cost
I was pondering switching barrels on my model 7 from a 243 to a 308. I want to step up a contour size and have a 20 or 22” finished barrel. I’ve never done this before and was wondering what I might...
View ArticleScope Mounting
When I mount a scope on a rifle I use blue Loctite on the base screws. However, when I attached the rings with the scope to the base I don't use any type of thread locker. I tighten the screws down...
View ArticleBeretta a400 youth stock and forend - Found One
I picked up a beater a400 with no forend and stock. I want to refinish it for my nephew who started shooting on his school team. Anyone out there have either or both of these parts? Condition is not...
View ArticleBuckmark issues
Anybody recommend a good gunsmith to go through a buckmark pistol? Having an issue and it's tedious work. Bob in palmetto said he didn't want to fool with it (fairly typical answer from him). Thx in...
View ArticleScrew repair
I had a supposed to be great long time in business gunsmith drill a Mauser 98 action for scope mounts and mount them. Went to put a scope on and its off. One of the mounts got drilled off center. Is it...
View ArticleThe Real Gunsmith
Mr. Selby has some great gunsmith info for free just watch a few of his videos and decide for yourself.Enjoy!
View ArticleS@W 9VE 9mm Jamming
1. Gun is spotless 2. Good Ammo (brass) 3. Tried different clips & ammo 4. Clean Ramp Gun is not ejecting the casing after it is shot. Also, bullet underneath casing(in clip) is not putting...
View ArticleSmith & Wesson M&P22 4.1" Semi Auto Pistol Firing pin
Having hard time finding a firing pin for this gun. I've done took it apart and I prefer to replace it myself if I can find the firing pin. Thought I'd ask here before taking it to gunsmith. I'm not...
View Article93 Mauser question
So I've been wanting to add a 7x57 Mauser rifle to my collection of deer rifles and finally managed to find one at a reasonable price in a pawn shop. The first thing I did was to order a set of "Go"...
View ArticleN. GA gunsmith needed - headspacing adj
I need a recommendation for gunsmith to reset the headspacing on my Marlin XL7. It's a simple barrelnut rifle much like a Savage. I live near Cumming, north of Atlanta.
View ArticleStevens 67 series E
As posted I have a Stevens 67E the pump is sluggish in it. Everything is clean however the pump still isn't smooth. Any ideas? The gun does work by the way.
View ArticleLose sight
I have a Ruger SR22 that I've carried countless hours. 50% in holster , 50% of the time just in my rear or front pocket. Last week as I was pulling it from my pocket I noticed the rear sight was off to...
View ArticleMarlin 336 gunsmith needed
I have a Marlin 336 that’s 45+ years old. It’s gotten where the lever will pop open to that first stage at the least little bump. I would like to find someone who could get this tightened back up for...
View ArticleWinchester 1873
I have come by an 1873 in 32 caliber. I need a gunsmith familiar with these guns to go through it and do any maintenance or repairs required. Any recommendations?
View ArticleBarrel cut and crown
I am looking for a gunsmith in the Augusta area to cut and crown a rifle barrel for me. Does anyone know of a reputable gunsmith in this area?
View ArticleModel 7 Stock
I have a Model 7 with what I assume is a walnut stock from the factory. I made a huge mistake and used some very strong bore cleaner without a bore guide. The bore cleaner ran down the stock, stripping...
View ArticleRuger 77 Rear sight base?
Where is a good place to find a Ruger 77 270 rear sight base? Also did Ruger ever make a steel floor plate to replace the Aluminum floor plates?
View ArticleWorth a shot to ask
I was wondering if anyone here knows if Charles Daly shotguns are parts interchangeable with another firearms brand? My 601 accepts, for example, Beretta/Benelli Mobil chokes. Was wondering if there...
View Article870 express
20 gauge express magnum: shells hang up in magazine; i have cleaned magazine tube. Wondering if my problem is the plastic magazine follower. No plug in the magazine.
View ArticleExtractor spring issue?
New shooter here,I purchased a new S&W M&P a long while ago. Last week I did two days of training, shot about 700 rounds. I had too many jams to count, all had to be cleared by mortar. The...
View Article
More Pages to Explore .....